Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Atherton, CA
Gate access control repair in Atherton typically costs $280-$620 for keypad or intercom fixes, while parts and welding jobs range from $180 for hinge work to $1,400 for full post replacement. Most calls we receive in the 94027 zip involve integrated systems wired into Crestron or Control4 home automation platforms, where a gate that won’t respond to a phone command is often a low-voltage wiring issue rather than a mechanical failure. Call (669) 900-1904 for a free estimate - we’ll diagnose the problem and give you a written price before any work starts.
Why Atherton Homes Are Different
Atherton’s 1-acre minimum lot requirement means every property has a long private driveway, and that distance changes the job. Conduit runs are longer, operators work harder on daily cycles, and a gate post that shifts even an inch throws a swing gate out of plumb across a much wider arc than on a standard suburban lot. The Peninsula’s clay-heavy soils swell during the wet season from November through March, then contract, and we’ve found hinge bolts loosened by that cycle on gates from the 1970s and on new ornamental iron installed last year.
The marine layer keeps hardware in near-constant moisture exposure. Terminal blocks inside buried motor housings corrode faster here than inland, and wrought-iron gates show rust at weld joints within five to seven years without maintenance. San Mateo County also requires permits for gate operator replacements that alter electrical service or structural footings - a detail that catches homeowners off-guard when they expect a same-day swap.
Our Main Atherton Services
These are the three services Atherton homeowners call us about most often.
Gate Repair in Atherton
We repair swing and slide gates on estates throughout Atherton, from mid-century properties near Selby Lane to newer builds off Isabella Avenue. The work ranges from resetting limit switches on Viking operators to realigning gates thrown out of true by post settlement after winter rains. Every repair includes a photo log of what we found and what we adjusted. Gate Repair in Atherton
Gate Installation in Atherton
New gate installations in Atherton must account for long driveways, integrated access control, and county permit requirements for operators that change electrical load. We measure the site, specify the operator capacity for daily cycle count, and deliver a written scope and price before ordering materials. Gate Installation in Atherton
Gate Motor & Opener in Atherton
Motor replacement on Atherton estates often involves swapping a BFT or FAAC hydraulic operator that has cycled 15,000 times per year across a deep driveway. We match replacement capacity to actual gate weight and length of travel, and we document limit-switch settings and amperage draw before leaving. Gate Motor & Opener in Atherton
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterGate Access Control in Atherton
Most Atherton access control calls involve systems tied to whole-home automation. A gate that opens from the Crestron panel inside but not from the driveway keypad usually traces to a failed RS-485 connection or a 24-volt transformer that dropped below threshold in the damp housing. We service Gate Access Control systems across the Peninsula, and in Atherton we expect to find multi-vendor integrations that require methodical voltage testing rather than guesswork replacement.
Keypad Entry
Signs you need it
The keypad beeps but the gate doesn’t move, or buttons respond intermittently after morning moisture.
What it costs in Atherton
Keypad repair or replacement typically runs $280-$480, including testing the low-voltage run back to the control board.
How we do it
We test voltage at the keypad, check the wiring harness for corrosion at buried splices, and photograph the terminal map before disconnecting anything.
Video Intercom
Signs you need it
The call button rings inside but video is black, or the gate release relay clicks without opening the operator.
What it costs in Atherton
Video intercom repair ranges from $340 for a power supply swap to $620 for full station replacement with coax or Cat6 re-run.
How we do it
We verify PoE voltage at the station, test the door-release relay against the operator’s dry-contact input, and document the IP address or analog channel for your integrator.
What Gate Access Control Costs in Atherton
| Item | Typical range in Atherton |
|---|---|
| Keypad entry repair/replacement | $280 - $480 |
| Video intercom repair | $340 - $620 |
| Phone entry system troubleshooting | $220 - $380 |
Why does my Atherton gate keypad work in summer but fail in winter?
Moisture intrusion at cable splices or terminal blocks is the usual cause; the marine layer condenses inside buried housings and corrodes low-voltage contacts. We seal splices with gel-filled connectors and photograph the wiring diagram before closing the housing.
Can you fix my gate intercom without disconnecting my Control4 system?
Yes - we test and document the RS-485 or IP settings before touching anything, then restore the exact same addressing so your integrator doesn’t need to return. Call (669) 900-1904 and we’ll review the setup over the phone first.
Gate Parts & Welding in Atherton
Welding and parts replacement in Atherton covers everything from hinge pins worn oval by 50 years of swing cycles to new posts set in concrete after clay-soil settlement. The marine layer accelerates rust on ornamental iron, and we’ve replaced entire lower rail sections where moisture collected behind decorative collars. We handle Gate Parts & Welding jobs from single hinges to full gate rebuilds, always with a written price before cutting or welding anything.
Hinge Replacement
Signs you need it
The gate drags at the latch side, or the hinge pin has visible play that lets the gate wobble in wind.
What it costs in Atherton
Single hinge replacement runs $180-$320; a full set of three on a heavy iron gate runs $420-$680.
How we do it
We support the gate with a portable jack, remove the pin and bracket, weld new J-bolts or bolt-through plates, and photograph the alignment before releasing the jack.
Post Replacement
Signs you need it
The post leans visibly or moves when you push the gate, or the concrete footing has cracked from soil expansion.
What it costs in Atherton
Post replacement with new concrete footing typically costs $880-$1,400, including temporary bracing and gate re-hanging.
How we do it
We excavate to 36 inches minimum, pour high-strength concrete with a post base anchored below frost line, and let it cure 48 hours before re-hanging the gate.
What Gate Parts & Welding Costs in Atherton
| Item | Typical range in Atherton |
|---|---|
| Hinge replacement (single) | $180 - $320 |
| Hinge replacement (full set) | $420 - $680 |
| Post replacement with footing | $880 - $1,400 |
Will welding fix my rusted iron gate or do I need full replacement?
Most rust damage is local - lower rails, scroll ends, or weld joints - and we can cut out the bad section, fabricate a matching piece, and weld it in. We photograph the damage, show you the repair plan in writing, and quote replacement only if the frame itself is compromised.
How long does a welded post repair last in Atherton’s wet climate?
A properly set concrete footing with a galvanized post base lasts 20-plus years; we use them on every post replacement and document the depth and mix in your job record. Call (669) 900-1904 for a free assessment of your post condition.
Brands We Service in Atherton
We stock parts and service nine automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most Atherton properties run BFT, Viking, or Linear operators, and we carry common control boards, limit switches, and remote receivers for same-day repair on those three. our brands
Pricing for Gate Repair in Atherton, CA
| Service | Typical range in Atherton |
|---|---|
| Keypad entry repair/replacement | $280 - $480 |
| Video intercom repair | $340 - $620 |
| Phone entry system troubleshooting | $220 - $380 |
| Hinge replacement (single) | $180 - $320 |
| Hinge replacement (full set) | $420 - $680 |
| Post replacement with footing | $880 - $1,400 |
| Gate alignment and track adjustment | $220 - $380 |
| Custom welding (per linear foot) | $140 - $240 |
| Roller replacement (slide gate) | $160 - $280 |
| Access control diagnostic (hourly) | $180 - $220 |
Prices in Atherton run toward the higher end of these ranges when we encounter integrated automation systems requiring coordination with your home-technology contractor, or when county permit work adds inspection scheduling. The flat price we write before starting covers everything in the scope - no additional charges for the photo documentation or the 365-Day Done Right Promise.
Neighborhoods We Serve in Atherton
We dispatch to properties across Atherton’s full 94027 zip, from the older estate parcels near the town center to newer construction on the western edge. Response time is typically under 90 minutes for urgent calls anywhere in town.
- Lindenwood
- West Atherton
- East Atherton (Selby Lane area)
- Valparaiso Park vicinity
- Isabella Avenue corridor
Service Area - Cities Near Atherton
Our crews work throughout the Peninsula, with regular calls in Menlo Park, CA to the south, Redwood City, CA along the 101 corridor, Palo Alto, CA to the east, and San Mateo, CA to the north. Dispatch and scheduling are coordinated from our San Francisco Bay Area office.
Serving Atherton, CA - Our Local Coverage Area
We’re based in the Atherton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Atherton
San Mateo County requires permits for gate operator replacements that alter electrical service or structural footings - not for simple repairs like hinge replacement or limit-switch adjustment. We flag permit requirements during our free estimate and can coordinate the application if needed.
For access control or mechanical failures that leave a gate stuck open or closed, we typically dispatch within 90 minutes anywhere in Atherton. A live person answers our phone 24 hours a day - no voicemail, no callback queue.
Yes - we document RS-485 addresses, IP settings, and relay configurations before touching anything, then restore them exactly. Your Crestron or Control4 programmer won’t need to revisit for a gate hardware repair.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Atherton Customers Say
"Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.